IMPLEMENTATION OF THE SERVO SG 90 MOTOR AS A MECHANICAL DRIVE IN E. I. HELPER (ELECTRONICS INTEGRATION HELMET WIPER)
Main Article Content
Abstract
Many motorcyclists face problems when it rains, visibility limited helmet glass when driving can be one of the factors that cause it traffic accidents. Wiper Helm or E. I. Helper is a tool for motorcyclists which has a function to clean the helmet glass from a limited visibility when it rains down, by adjusting the measurement angle calculation 00-1100, with the average duration delay time 3.35 seconds to clean the helmet glass back and forth, the experiment was carried out 9 times on the helmet glass with a stable testing success rate. In the E. I. Helper mechanical movement system that has been installed to program data through the Arduino IDE application, the SG 90 Servo Motor mechanical drive system is used and the Arduino Nano Atmega 328 microcontroller. Mechanical motor Servo SG 90 on the circuit E. I. Helper will have an active status of electric power flowing with a push button switch while ON condition The E. I. Helper circuit will have an inactive status when the push button switch is OFF.
Downloads
Download data is not yet available.
Article Details
How to Cite
Salim, A., Saragih, Y., & Hidayat, R. (2020). IMPLEMENTATION OF THE SERVO SG 90 MOTOR AS A MECHANICAL DRIVE IN E. I. HELPER (ELECTRONICS INTEGRATION HELMET WIPER). Electro Luceat, 6(2), 236-244. https://doi.org/10.32531/jelekn.v6i2.256
Section
Articles
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
References
[1] Hilal, A., dan Manan, S., (2013), "Pemanfaatan Motor Servo sebagai Penggerak CCTV untuk Melihat Alat-Alat Monitor dan Kondisi Pasien di Ruang ICU", Gema Teknologi, vol. 17, no.2.
[2] Rinaldy, Christianti, R. F., dan Supriyadi D., (2013), “Pengendalian Motor Servo Yang Terintegrasi Dengan Webcam Berbasi Internet Dan Arduino”, Jurnal Infotel, vol. 5.
[3] Latifa, U., dan Saputro, J. S., (2018), “Perancangan Robot Arm Gripper Berbasis Arduino Uno Menggunakan Antarmuka Labview”, Jurnal Barometer, vol.3, no.2, pp. 138 – 141.
[4] Kurniawan, A. H., dan Rivai, M., (2018), “ Sistem Stabilisasi Nampan Menggunakan IMU Sensor dan Arduino Nano”, Jurnal Teknik ITS, vol. 7.
[5] Muchtar, H., dan Hidayat, A., (2017), “Implementasi Wavecom Dalam Monitoring Beban Listrik Berbasis Mikrokontroler” Jurnal Teknologi, vol. 9 no.1.
[6] Eriyani, V., Triyanto, D., dan Nirmala, I., (2018), “Rancang Bangun Robot Pelayan Restoran Otomatis Berbasis Mikrokontroler ATMEGA 16 Dengan Navigasi Line Follower”, Coding Sistem Komputer Untan, vol. 6, no. 3, pp. 66 – 74.
[7] Hamrul, H., Waluyo, A., dan Busyran, M., (2011), “Rancang Bangun Alat Pengontrolan Daur Ulang Solar Bekas Dengan Mikrokontroler AT89C51” Jurnal Ilmiah D’ComPutarE, vol.1
[8] Saragih, Y., Hakim G. R., Elisabet A., dan Roostiani H. A., (2019), “Monitoring Design of Methods and Contents Methods in Semi Real Water Tandon by Using Arduino–based on Internet of Things”, IEEE, pp. 1- 4.
[9] Nusyirwan, D., Aritonang, M. D., dan Perdana P. P . P, (2019), “Penyaringan Air Keruh Menggunakan Sensor LDR dan Bluetoth HC – 05 Sebagai Media Pengontrolan Guna Meningkatkan Mutu Kebersihan Air di Sekolah”, Logista Jurnal Imiah Pengabdian Kepada Masyarakat, vol. 3, no.1.
[10] Hidayat, R., (2017), “Pengembangan Alat Ukur Kadar Air Padi (GABAH) Untuk Mewujudkan Pertanian Industrial Di Kabupaten Indramayu, “Creative Research Jurnal, vol. 2, no. 1, pp. 55 – 68.
[2] Rinaldy, Christianti, R. F., dan Supriyadi D., (2013), “Pengendalian Motor Servo Yang Terintegrasi Dengan Webcam Berbasi Internet Dan Arduino”, Jurnal Infotel, vol. 5.
[3] Latifa, U., dan Saputro, J. S., (2018), “Perancangan Robot Arm Gripper Berbasis Arduino Uno Menggunakan Antarmuka Labview”, Jurnal Barometer, vol.3, no.2, pp. 138 – 141.
[4] Kurniawan, A. H., dan Rivai, M., (2018), “ Sistem Stabilisasi Nampan Menggunakan IMU Sensor dan Arduino Nano”, Jurnal Teknik ITS, vol. 7.
[5] Muchtar, H., dan Hidayat, A., (2017), “Implementasi Wavecom Dalam Monitoring Beban Listrik Berbasis Mikrokontroler” Jurnal Teknologi, vol. 9 no.1.
[6] Eriyani, V., Triyanto, D., dan Nirmala, I., (2018), “Rancang Bangun Robot Pelayan Restoran Otomatis Berbasis Mikrokontroler ATMEGA 16 Dengan Navigasi Line Follower”, Coding Sistem Komputer Untan, vol. 6, no. 3, pp. 66 – 74.
[7] Hamrul, H., Waluyo, A., dan Busyran, M., (2011), “Rancang Bangun Alat Pengontrolan Daur Ulang Solar Bekas Dengan Mikrokontroler AT89C51” Jurnal Ilmiah D’ComPutarE, vol.1
[8] Saragih, Y., Hakim G. R., Elisabet A., dan Roostiani H. A., (2019), “Monitoring Design of Methods and Contents Methods in Semi Real Water Tandon by Using Arduino–based on Internet of Things”, IEEE, pp. 1- 4.
[9] Nusyirwan, D., Aritonang, M. D., dan Perdana P. P . P, (2019), “Penyaringan Air Keruh Menggunakan Sensor LDR dan Bluetoth HC – 05 Sebagai Media Pengontrolan Guna Meningkatkan Mutu Kebersihan Air di Sekolah”, Logista Jurnal Imiah Pengabdian Kepada Masyarakat, vol. 3, no.1.
[10] Hidayat, R., (2017), “Pengembangan Alat Ukur Kadar Air Padi (GABAH) Untuk Mewujudkan Pertanian Industrial Di Kabupaten Indramayu, “Creative Research Jurnal, vol. 2, no. 1, pp. 55 – 68.